Detergent cartridge not detected in the dispenser.
This is on select models. If you are using single-load doses of detergent, ignore this message.
Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely.
Int
The cycle was paused or canceled.
The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time.
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
rL or F34
Items were detected in the washer during the Clean Washer cycle.
Remove items from the drum and restart the Clean Washer cycle.
Sud or Sd
There are too many suds in the washing machine.
The washer will not be able to spin out water with the excess suds. When "Sud" or "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the tumbling and adds water for additional rinsing. This pause allows the bubbles in the suds to break. This pause and rinsing are necessary and may occur several times to eliminate the suds.
Make sure you are using HE or High Efficiency detergent.
If you used "no splash" or "easy pour" liquid chlorine bleach, you could also have too many suds. This type of liquid chlorine bleach contains a thickening agent that may create excess suds in washers. If this is the case, run the washer with regular liquid bleach products.
The Sud or Sd code may also be the result of a restricted drain hose or standpipe (drainpipe). Make sure that the drain hose is not kinked or clogged. Find more information on How to Install the Drain Hose.
F5 E2
The door is not locking properly.
Check that there are no items blocking the door and it is closing completely. Press the Pause or Cancel button twice and the Power button once to clear the code.
F7 E1
Indicates a motor speed sensing error,
The motor can not achieve the correct speed for the cycle selection. Check that:
All the shipping bolts have been removed
The washer has not been overloaded
Press the Pause or Cancel button twice and the Power button once to clear the code.
F8 E1 or LO FL
The washer is sensing a low flow of water.
Check that:
The household water supply is turned on and both the cold and the hot water faucets or valves are fully open.
Press the Pause or Cancel button twice and the Power button once to clear the code.
F8 E2
Indicates there is a problem with the Dispenser System
This is on select models. Verify detergent drawer or detergent cartridge is not clogged with detergent.
F9 E1
Indicates that drain times are longer than expected, typically over eight (8) minutes.
Make sure the drain hose is not kinked or clogged. Use the U-shaped drain hose form on the drain hose. The standpipe (drainpipe) height requirements are 96" (244 cm) maximum and 39" (99 cm) minimum.
Excessive suds may also cause delays in draining. Make sure you are using HE detergent.
Other F# E# code
Indicates other error
Unplug the washer or disconnect the power for one minute and reconnect it again. Reselect the cycle and press Start. If the code persists, Contact Us.
Русский
English
If none of these solutions work, Contact Us
This is on select models. If you are using single-load doses of detergent, ignore this message.
Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely.
The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time.
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
The washer will not be able to spin out water with the excess suds. When "Sud" or "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds. During this time, the washer pauses the tumbling and adds water for additional rinsing. This pause allows the bubbles in the suds to break. This pause and rinsing are necessary and may occur several times to eliminate the suds.
Make sure you are using HE or High Efficiency detergent.
If you used "no splash" or "easy pour" liquid chlorine bleach, you could also have too many suds. This type of liquid chlorine bleach contains a thickening agent that may create excess suds in washers. If this is the case, run the washer with regular liquid bleach products.
The Sud or Sd code may also be the result of a restricted drain hose or standpipe (drainpipe). Make sure that the drain hose is not kinked or clogged. Find more information on How to Install the Drain Hose.
The motor can not achieve the correct speed for the cycle selection. Check that:
Press the Pause or Cancel button twice and the Power button once to clear the code.
Check that:
Press the Pause or Cancel button twice and the Power button once to clear the code.
This is on select models. Verify detergent drawer or detergent cartridge is not clogged with detergent.
Make sure the drain hose is not kinked or clogged. Use the U-shaped drain hose form on the drain hose. The standpipe (drainpipe) height requirements are 96" (244 cm) maximum and 39" (99 cm) minimum.
Excessive suds may also cause delays in draining. Make sure you are using HE detergent.